Skip to content

Scheppach GP650 review

3,300 l/h, 35 m (115 ft) head, 3.5 bar and an 8 m (26 ft) suction height, with G1" suction and delivery ports.

What the maker prints on its own page

A powerful 600 W motor delivering up to 3,300 l/h, stated as ideal for garden watering and for drawing water from wells, cisterns, rain butts and ponds. A head of up to 35 m (115 ft), 3.5 bar of delivery pressure and a suction height of up to 8 m (26 ft) supply lawn, beds, hedges and irrigation systems. Durable G1” suction and delivery connections let the pump be joined to ordinary garden hoses, fittings and irrigation systems. An integrated overload protection guards the motor against overheating and a carry handle allows transport.

Four figures, which is the whole curve

Flow, head, pressure and suction height. Nine pumps on this shelf and this is one of the few to publish all four.

The two that matter together are flow and head, and they are the opposite ends of one line:

3,300 l/h is measured with the outlet open and nothing to lift. 35 m is measured with the outlet closed and nothing moving.

Real operation is somewhere between, on a curve no domestic listing publishes. A pump with a high head has pressure in reserve when there is also flow, which is why the head figure matters even though you will never see 35 meters (115 ft).

The thread, named

G1”. That is a parallel pipe thread, and the standard it comes from is titled, in effect, “pipe threads where pressure-tight joints are not made on the threads”.

Which means the joint is sealed by a flat washer against a face, not by the thread. A G-fitting screwed on hard without its washer will leak, and tightening it further deforms the plastic.

Naming the thread family saves a buyer the leak. Most of this shelf gives an inch size and stops.

What is not stated

The housing and impeller materials, which the cheaper pump below this one names. And no drain plug — on a machine that will spend a winter somewhere cold, that is the omission worth checking before buying.

Availability

Listed and unsold: the American Amazon catalog holds the reference with nobody behind it.

Taken from Keepa on the day this page was last revised; stock and prices move without notice.

The declared figures, and the point they stop at

Strengths

  • Flow, head, pressure and suction height all published — the complete hydraulic picture
  • The thread family is named: G1", which is the parallel type sealed by a washer
  • Overload protection against overheating, stated

Compromises

  • No housing or impeller material published
  • No drain plug mentioned, on a machine that lives outdoors
  • Priced in two of the six markets this site follows

Specifications

Flow rateUp to 3,300 l/h, at zero head as the convention requires
HeadUp to 35 m (115 ft), at zero flow — equivalently 3.5 bar
Motor power600 W, with integrated overload protection
Suction heightUp to 8 m (26 ft), as stated
ConnectionsG1" suction and delivery, as stated
MaterialNot published
WeightNot published — a carry handle is stated
Amazon referenceB0GTFR575S (one reference across 6 Amazon marketplaces)
EAN4046664288732

What this machine usually gets asked

Is 35 m (115 ft) of head the same as 3.5 bar?

Near enough: one bar is roughly ten meters of water column, and the listing gives both, which is the correct way to publish it. Both are measured at zero flow — the outlet closed — and neither happens while water is moving.

What does G1" mean?

A parallel pipe thread in the one-inch size, from the standard whose own title says the joint is not sealed on the threads. It is sealed by a flat washer against a face, which is why a G-threaded fitting without its washer leaks however hard you tighten it.

Can it run a sprinkler at the end of a long hose?

At 3.5 bar it has pressure in reserve for that. What arrives depends on the hose bore, its length and every quick coupling in between, and this page prints the pump figures rather than predicting the result at your sprinkler.

Our score

7.8/ 10

The first listing here to give all four hydraulic figures — flow, head, pressure and suction height — and both port threads. 3,300 l/h at zero head, 35 m (115 ft) at zero flow, 3.5 bar, 8 m (26 ft) of lift, on G1" connections that take ordinary garden fittings.

This one and its buyer, among lawn equipment

A medium garden watered from a butt or a cistern, where the numbers need to be checkable before buying

The lawn equipment guides that feature it

Sources

Specifications: the Amazon.com listing, read from a US address. Live prices: Amazon.com, through Keepa. Every figure on this page names its source.

The way we judge this lawn equipment

The live figure beside a product went and asked the shop for it the moment this page opened; any amount written into the text has not moved since the sentence was drafted, and it is the first of the two that counts.